Small Pignose Amp Schematic?

[Arn C.]

Howdy All,
   I was given a junk Pignose, the little portable, with the "pignose" on the front model 7-100-(R)  It has roughly a 5" speaker.

   One of the two transformers on the circuit board was not soldered onto the board, and I do not know which way to orientate it.  It is the larger transformer.  (both sides of this transformer has 3 taps)
    Anyone have a schematic or knows which way the transformer goes into the board?  The larger transformer also has a red stripe on the top on one side of it, if that helps.
    Also I just measured each side(ohms)  The red stripe side has 1.9 ohms outer tap to outer tap, the other side is 5.1 ohms outer tap to outer tap.

Thanks!
Arn C.

[Mark Hammer]

I don't have it on me at the moment, but I believe it was posted around since I know I snagged it somewhere on-line.

[B Tremblay]

[Arn C.]

Thank you so much!  Exactly what the doctor ordered!

Peace!
Arn C.

[Marcos - Munky]

Check your e-mail for the schematic.

[Arn C.]

Thanks Marcos!!!  There was one wire where I didn't know where it went!

Thanks again!!!
Peace!
Arn C.

[Tubebass]

Could I get a copy of that too, please?

[D Wagner]

Is there a chance that I could get that schematic, too?  I have some transformers for that type of amp that need a good home.

Thanks in advance!

Derek

datilderek@excite.com

[djmartins2]

Hi,

Could y'all also send a copy to
djmartins2 @ comcast.net

I searched the web and couldn't find a copy anywhere!

thanks,
DJ

[Marcos - Munky]

Schematic sent. Hey Tubebass, I need your e-mail address.

[Gilles C]

Ahhh, I hate to say this... but I would like a copy too.  :oops:

My address is good if you click on the author's name on the left.

Thanks,

Gilles

[Gilles C]

thanks again

[javacody]

Marcos, could I get a copy too?

c.fyler at mchsi.com

[Marcos - Munky]

Schematic sent.

[Torchy]

Marcos, thanks for the schemo guy

[Gilles C]

While checking the Pignose schematic Marcos sent me, I remembered this excellent one.

http://www.redcircuits.com/Page52.htm

I wanted to make a pcb layout for it, but ... it's still not done.I would be curious to compare it to the sound of a Pignose. I like discrete  :lol:

Gilles

[toneman]

nice link.
thanx Gilles!
tone

[casperssoul]

I need help with a vintage pignose 7-100 r. I have worked with it enough to get sound out of it. When I received it the batteries has destroyed the majority of the existing wiring for the input & power switch/vol knob. The battery pack has been removed and would love to just leave it as a plug in amp as I do not care about the battery power nor do I want to corrode the repaired solder joints. I have photos i can supply.. I have the schematic as well, although, it confuses me, I have done guitar restores in the past

[casperssoul]

Red wire i believe was originally the battery positve.
http://s92.photobucket.com/user/evon_ishot/media/WP_20140626_0042014062716143220140627161622.jpg.html

Blue wire shows as a ground by way of volt meter.
http://s92.photobucket.com/user/evon_ishot/media/WP_20140626_0042014062716143220140627161726.jpg.html

Black wire shows as a ground by way of volt meter. Which i believe to be oringally battery ground..
http://s92.photobucket.com/user/evon_ishot/media/WP_20140626_0052014062716182020140627161948.jpg.html

This is my power switch/input side as i recieved it..
http://s92.photobucket.com/user/evon_ishot/media/WP_20140626_006.jpg.html


Where do these wires go!? If I use black to the top of input that is empty but has old solder on it in photo and twist the blue and red together I get sound.. although it is very low and very fuzzy..