AMZ FX ANALOG ALCHEMY GEOFX MEF ROG MEF DIY WIKI

Schematic to Breadboard nightmare!

Started by maurice, October 12, 2011, 05:01:04 PM

Previous topic - Next topic
Print
Go Down Pages 1 2
User actions

deadastronaut

#20
October 24, 2011, 04:27:37 AM
i'll chime in again....heres a diagram/layout with your breadboard style...
make sure you have your in/outs grounds are connected to your board, ... and your breadboard positive and negatives connected on the top and bottom rails of you breadboard ok....
this should be ok...do it carefully and you'll be fuzzing.... ;)
https://www.youtube.com/user/100roberthenry
https://deadastronaut.wixsite.com/effects

chasm reverb/tremshifter/faze filter/abductor II delay/timestream reverb/dreamtime delay/skinwalker hi gain dist/black triangle OD/ nano drums/space patrol fuzz//

Main.Ace.FX

#21
October 24, 2011, 09:03:39 AM
I feel your pain Maurice, I make stupid mistakes all the time, and they are always the hardest to diagnose!!  Sometimes I find it best to clear everything off the breadboard and start again fresh.  A lot of times, my errors correct themselves....good luck, stick with it!!

maurice

#22
October 24, 2011, 09:14:07 AM
You'll never believe it... IT WORKED!!!!! I have wonderful fuzzy goodness thanks to DeadAstronaut's last breadboard.

It may have taken a while but I got there in the end.  I almost can't contain myself!

Big thanks guys, I was ready to give up but your advice was amazing.

Next step.... soldering :)

Main.Ace.FX

#23
October 24, 2011, 09:24:32 AM
way to go!!

deadastronaut

#24
October 24, 2011, 09:25:35 AM
whooooo hooooooooooo.........glad ya got it sorted..and had the patience to sort it.... ;)
https://www.youtube.com/user/100roberthenry
https://deadastronaut.wixsite.com/effects

chasm reverb/tremshifter/faze filter/abductor II delay/timestream reverb/dreamtime delay/skinwalker hi gain dist/black triangle OD/ nano drums/space patrol fuzz//

alparent

#25
October 24, 2011, 09:31:10 AM
Perfect 10 for perseverance.  :icon_smile:

markeebee

#26
October 24, 2011, 09:46:41 AM
Perfect 10 for DeadAstro as well, for knocking up that diagram. Very kind.

maurice

#27
October 25, 2011, 05:34:11 AM
Final question then I swear I'm putting this topic to rest :)

I'll be using a DPDT switch on the final board.  How can I add an LED light to the circuit?

DavenPaget

#28
October 25, 2011, 05:50:43 AM
Quote from: maurice on October 25, 2011, 05:34:11 AM
Final question then I swear I'm putting this topic to rest :)

I'll be using a DPDT switch on the final board.  How can I add an LED light to the circuit?

http://gaussmarkov.net/wordpress/thoughts/wiring-up-a-1590b/ IF you use a 3PDT , in the past if i had a DPDT i did a separate switch  :icon_redface:
Hiatus

Main.Ace.FX

#29
October 25, 2011, 06:19:19 AM
Just use a 3pdt switch

alparent

#30
October 25, 2011, 07:44:12 AM
If using a DPDT you can use a Millenium bypass.

Read up on it
http://www.geofex.com/Article_Folders/Millenium/millen.htm
http://www.geofex.com/Article_Folders/Millenium/mill2.jpg
http://www.geofex.com/Article_Folders/bypass/bypass.htm

Tip-of-the-day! Get to know R.G.'s site (Geofex) ...... lots of wonderfull info.
Print
Go Up Pages 1 2
User actions