ridiculously simple cab sim : /

[anotherjim]

Nearly finished

[deadastronaut]

you know me better than that ha ha,....


last night i was thinking of adding a mid control just for a laugh....

will try it later...

[GibsonGM]

PASSIVE DI = 100n nice n bassy...  470n nice n tight

LINE IN  = 100n nice n tight ....470n nice n bassy...

Well, you can't beat that, now can you?  

It's hard to know when something is "done", isn't it??

[deadastronaut]

yep it certainly is...

its like a painting...do i, or dont i...add a little....hmmmm....

or not.....hmmmm...

[J0K3RX]

Was bored last night so I tried to make a little 1590A SMD layout for this.. Haven't really made a layout in a while so I did this as practice..  If anybody wants it I will give a link to the diptrace file. You will probably end up needing it because Rob changes his mind like a woman changes clothes... 

[deadastronaut]

oi!.....true though.




your gonna have to change that.......lots of times..

[vigilante397]

Was bored last night so I tried to make a little 1590A SMD layout for this.. Haven't really made a layout in a while so I did this as practice..  If anybody wants it I will give a link to the diptrace file. You will probably end up needing it because Rob changes his mind like a woman changes clothes... 

I'll definitely take you up on those diptrace files. I had a brief SMD phase and never got around to using up all my components

[askwho69]

. "You will probably end up needing it because Rob changes his mind like a woman changes clothes...  "

Funny hahaha but its true though


Sent from my iPhone using Tapatalk

[deadastronaut]

heres where i am.....after changing my dress over and over

(mike, try this out see what you think....)

[2manygadgets]

I have to say, I'm really excited to try this out. The sound samples sounds fantastic!

I have a Rivera MiniRockRec which works great for recording because I'm using Two Notes Wall of Sound to simulate speakers in my DAW. I was hoping I'd be able to use it for late night practicing too so I don't wake up the family however even though the Mini does have a headphone jack, the speaker simulations don't work with it. They only put a low pass filter on the headphone jack and I think it sounds bad.

Looks like this is a line level signal but could I put this in between the headphone out of the MiniRockRec or would the signal coming from the headphone jack not be enough? Otherwise, I could plug this between the line out of the Mini and into my Interface. I have a headphone out from my Focusrite so I could use that. It would be great because as of now, using the Focusrite, I either have latency if I use WoS or I hear the unfiltered raw signal coming from the line out which also sound like crap of course.

I don't know much about building circuits like this, I literally ordered a cheap breadboard kit on Amazon today. I want to know, i don't see it mentioned, is the pot you have called out a linear or audio taper? Also when I called a small local shop about resistors/capacitors, I was asked if the resistors were 1/4 watt and what voltage the capacitors were. I could not tell from the schematic. I'm sorry if it was somewhere on the post and I missed it. I looked while I was on the phone but couldn't find any references to it.

[deadastronaut]

hi, the 'air' pot is a 1MA   A=LOG.   the 'mid' pot is a B= LINEAR.

1/4 watt resistors are perfect.

electro caps , get 25v-50v and you'll be fine.

yep, i have the same need, where i just want to plug in to a DI box or line in...(mixer)

for late night noodling, and just for convenience as sometimes i leave my amp
at friends /studio etc...but i always bring my pedals home..

i do have a digital multi fx board with cab sim built in, but i prefer my own dirts..


anyway, i'll test this more tomorrow...and see if my ears like it then. my ears change from day to day i find as i get older   

[GibsonGM]

Oooh, a mid control!  FANCY!   I'll check that out soon, Rob...spent the day prepping and painting pine floors in my farmhouse...a little tired and in need of a beer or 4...my elec. room is up here where the floor paint is drying (volatile....ack..).

Nice work on that! 

[deadastronaut]

enjoy the beer man, sounds like you earned it... 

[GibsonGM]

enjoy the beer man, sounds like you earned it... 

Ya, pix later!   

[askwho69]

 I think the cab needs more low end


Sent from my iPhone using Tapatalk

[deadastronaut]

You may be right....i,ll listen again later, and post clips...

get it on ya breadboard, join in...

[askwho69]

I don't have breadboard right now, I will buy this week for much more fun .


Sent from my iPhone using Tapatalk

[Hatredman]

We're all waiting for page 36...   

Os this the title of a Syd Barrett song,?


here be .sig

[2manygadgets]

I'm trying to put this together. I have little experience with bread boarding. I've built two pedals from kits but that's it so far. Any chance you could post a shot of how this circuit looks on the bread board? I tried doing a tutorial which helped some but I have many questions of how this should work.


Sent from my iPhone using Tapatalk

[2manygadgets]

Did I ask for something that's totally gauche? This forum thread stopped completely after my last post asking about a picture of how to put this together on a bread board... Very sorry if this was out of turn.