Pictures!

[Govmnt_Lacky]

By the way this is the stock (block) version.The mods were just added upon housing the unit.

I am very interested in knowing where you tapped the circuit so you could switch between the Phase 45 and Phase 90 

Been looking for a good way to do that 

[cloudscapes]

cloudscapes, impressive as always! I especially like the LED indicators. About the chip you're using - it's a 328, isn't it. Isn't it overkill for what it does? The ease of reprogramming it kinda compensates for that, but I'd go the ATtiny45/assembly way... then get distracted by a housefly and abandon the project for good, but that's another story.

an 88. I tried a tiny but it didn't like what I was doing with 3 timers and two PWM channels 

[fretzburner]

By the way this is the stock (block) version.The mods were just added upon housing the unit.

I am very interested in knowing where you tapped the circuit so you could switch between the Phase 45 and Phase 90 

Been looking for a good way to do that 

Looking at my perf layout disconnect pin7 of IC3 from the circuit and solder wires on each disconnected points.pin7 is the 90 and the other is the output.now solder a wire from pin7 of IC2 and that wire is the 45.Switch SW1log-45,SW2log(center)-out,SW3log-90.Just using two stages instead of four results phase45.I hope this helps.

fretz

[a soBer Newt]

Here is my last custom effect
Bass drive:

I really like the idea of SMT on one side and through hole on the other!

[skullservant]

This first one started out as a lofi-delay kit from Synthrotek. It's made more for synth levels, so it needed a booster before it. I put a Madbean Thunderpuss before the delay circuit so that there isn't a volume drop, with volume control stashed away on the side. I switched out both knobs from the kit for 500k's, and now it can go from slapback delay all the way to cricket chirping. The toggle in the center turns on the LDR in the bottom right of the pedal so I can get Wow And Flutter effects on the fly with my foot. I also added CV to the delay pot, so I can plug in an external LDR and theoretically control the pedal with both the LDR on the pedal itself as well as the external LDR. It gets insane.



Next one is a Foxx Tone Machine clone using a Madbean Board. I fell in love with this enclosure size.




Lastly, a four knob RAT from a Madbean Board.

[tasos]

Lol the tone machine looks empty!
Hard time wiring it?

[rousejeremy]

Plexidrive with microamp. I'm going to replace the microamp with a demeter mid boost, not too impressed with the way the microamp interacts with it.

[fretzburner]

And here are my other builds
Dual Delay

Auto Wah

Boost and 2 OD

Compressor

Dual Chorus

[skullservant]

Lol the tone machine looks empty!
Hard time wiring it?

Nah. I like huge enclosures. I also didn't like the spacing of the board mounted pots, so I put wires on them so I could space them out. I didn't feel like adding a useless wire for the LED so I just wired it to the board, it makes it stay in place more-so than if I added a wire. I'm a big fan of securing my boards down some way or another. It makes me feel uneasy when I open a pedal and the board is floating.

[skullservant]

Lol the tone machine looks empty!
Hard time wiring it?

Nah. I like huge enclosures. I also didn't like the spacing of the board mounted pots, so I put wires on them so I could space them out. I didn't feel like adding a useless wire for the LED so I just wired it to the board, it makes it stay in place more-so than if I added a wire. I'm a big fan of securing my boards down some way or another. It makes me feel uneasy when I open a pedal and the board is floating.

But YES. Extremely hard time wiring it up. Took me a minute to get the joke 

[pinio]

Baja Sonic Stomp

[frequencycentral]

[teej212]

might want to reconsider the FC UK name, its been taken by a clothing company

[frequencycentral]

might want to reconsider the FC UK name, its been taken by a clothing company

Yeah but they sadly lack the arrow.......I can't fit 'Frequency Central' across Euro like I can for my pedals, hence 'FC>UK'. If French Connection come after me I'll change to 'FU>CK', thus making the pre-lawsuit FC>UK modules instantly collectable classics. Now, if French Connection happen to release any pedals or synth modules they can expect to receive a strongly worded letter from my mum.

[frequencycentral]

.....and just finished this batch for Joe's Pedals:

[nomorebetts]

might want to reconsider the FC UK name, its been taken by a clothing company

... thus making the pre-lawsuit FC>UK modules instantly collectable classics. Now, if French Connection happen to release any pedals or synth modules they can expect to receive a strongly worded letter from my mum.

[Slade]

might want to reconsider the FC UK name, its been taken by a clothing company

Yeah but they sadly lack the arrow.......I can't fit 'Frequency Central' across Euro like I can for my pedals, hence 'FC>UK'. If French Connection come after me I'll change to 'FU>CK', thus making the pre-lawsuit FC>UK modules instantly collectable classics. Now, if French Connection happen to release any pedals or synth modules they can expect to receive a strongly worded letter from my mum.

Hey Frequency United Central Kingdom, those boxes are COOL!

[chi_boy]

Baja Sonic Stomp

Love that finish.  Very nice work.

[deadastronaut]

@rick: fc>uk-ing awesome synth stuff...!...

[Ummagumma]