Pictures!

[Pyr0]

Here's my take on a Rat, I'm also making one for a mate, but it will be a polished box with the same rat design etched into it.



I'm still just building it, can't wait to see it with the led lighting. 

[kaycee]

Centaur built on perf. OA126s in the diodes (I like these, can you tell?). The Fv is 6.5 on them, which is really high for a Germanium diode. Sounds worlds better than the last Centaur I built. I used Madbean's Sunking schematic.

'My Little Klony' - thats hilarious

[kupfer_m]

My newest : Valvecaster with 7pin miniature tubes. Can be used with both 6C4 (=1/2 12AU7) and 6AB4 (=1/2 12AT7).
Runs on a slightly higher voltage of 20V. Heater voltage is 12 with heaters is series.

[davent]

^That is super nice, love the colour and matt finish you've acheived and cool jack "bezel". What type/brand of toggle switch did you use there?

dave

[Nikolay]

My newest : Valvecaster with 7pin miniature tubes. Can be used with both 6C4 (=1/2 12AU7) and 6AB4 (=1/2 12AT7).
Runs on a slightly higher voltage of 20V. Heater voltage is 12 with heaters is series.

BEAUTYYYYYYY! Amazing colors man!
Respect !!!

[Nikolay]

And this is my final project. I finish this looper 2 days ago.
It's a 12 channel custom programmable stompbox footcontroller with a lot of options and presets






Niki

[cloudscapes]

Holy Mother of Jacks! 

looks like a super clean build! nice one! guts?

[Nikolay]

Thanks. I forget to make a picture inside the looper. Next time

[Magnus]

Hello together,
it took a long time but now I have finished another pedal, so here is my "FUZZ FACE Vintage Germanium",
I tried everything to get the real look and "vintage-mojo-vibe", such as the wire-colors, the solder-lug on the pcb,
the right jacks and so on, here are the details:

- Enclosure: Type B
- etched Pertinax-PCB (screws screwed into glue-sockets)
- matched PNP-Germaniumtransistors Type NKT275 from DSI
- 1N34A-Germanium-Diode
- matched Carbon-Film-Resistors
- Vishay BC (Electrolytic-) Input-Capacitor, matched to 2,5uF
- NOS Siemens (Polystyrene-) Output-Capacitor, matched to 10nF
- Philips BC 123, 22uF / 16V (Elektrolytic-) Ground-Capacitor, matched to 20uF
- Bias-Trimpot for Q2
- quality Miyama-Toggleswitch
(de/activates Transistor-Stabilisation with 1N34A)
- positive ground
- low current-led

...yes, the DSI's are not real vintage-mojo but they sound good,
I will try AC128's too when I have the second fat-sized one for Q2...











Greetings
Magnus

[NazzTazz]

LoveP€dal Purple Plex| 8OO Clone... (Re-named JCM800, yep I know, not my best idea).

A little boo-boo on artwork (left leg of M)


Funny, I wanted a pure cyan for JCM, and printer did it greenish. I'm colorblind tho, but I think it's more green than cyan.


Still those boring bubbles between design and enclosure... I tried: putting a bit of water on the box before applying, making pinholes to let bubbles escape... I'm definitely bad at applying stickers.


Guts: This is a one-shot build, so I didn't plan the layout. Board could be smaller, components more evenly-spaced... Still makes the job, tho.


I wish I could get 1$ for each guy who thinks "Hey dude, your offboard wiring sucks".

[edd29]

ISP DECIMATOR

[musiclikscreams]

An old fuzz face clone I did years ago. I swapped out the trannies and a dead pot and wrapped it up in notebook paper last night

Gotta admit I stole the labeled knobs idea from here haha. I forgot who it was that just recently posted one. Props/cred goes to him

[Leston Braun]

An old fuzz face clone I did years ago. I swapped out the trannies and a dead pot and wrapped it up in notebook paper last night

Gotta admit I stole the labeled knobs idea from here haha. I forgot who it was that just recently posted one. Props/cred goes to him

Nice! Did you glue the paper on or is it just held by nuts on pots and jacks?

[musiclikscreams]

Nice! Did you glue the paper on or is it just held by nuts on pots and jacks?

Looked all over the house and couldn't find glue lol. So I just taped it inside the enclosure. On my next build I'm goin to glue it and give it a few layers of clear coat

[Jurassic]

Greetings
Magnus

Wow! Nice work! I really like this one!

[Thomeeque]

 Already presented multi-FX for my bandmate, now powder-coated and with slightly better but still temporary sticker (and shot in outer space this time ):



T.

[deadastronaut]

^ very cool.....you spelt colour wrong   

[darron]

^ very cool.....you spelt colour wrong   

that's only for us English speaking people... they have a variant on the language called American i believe...

[Thomeeque]

 One way or another the *proper* clone must clone even spelling errors to achieve original mojo

[jimmybjj]

My latest effort, all smd resistors on back of pcb