DIY Layout Creator - software for easy drawing PCB, vero and perfboard layouts

Perrow · March 01, 2013, 07:31:21 AM

Quote from: deadastronaut on March 01, 2013, 07:29:48 AM
man, i'm sad...

On the bright side, we pushed the thread to page 101.

deadastronaut · March 01, 2013, 07:34:36 AM

good, i feel better now!..

stirfoo · March 01, 2013, 06:22:21 PM

Thanks Perrow. I've rearranged it a bit after correcting the relay width (as ICs on the board). It should just have an empty strip at the top and bottom now.

Probably still need to proof-read it about 10 more times.

http://i.imgur.com/wWxj90L.png

And I just noticed I don't have cuts under some of the relays.

Perrow · March 01, 2013, 07:03:02 PM

Quote from: stirfoo on March 01, 2013, 06:22:21 PM
Probably still need to proof-read it about 10 more times.

If you're anything like me, it'll need one more proof-reading after it's built (independent of how many times you've proof-read it before building it). I can have up to about five components before that rule works every time, with less components it's intermittent.

Perrow · March 03, 2013, 05:19:09 PM

Bancika, any estimate when you've fixed the "Copy throws error" bug? It's highly annoying for someone who copy/pastes a lot and can't open the file in the previous version

I know you work on this in bursts (is it a Burstbox program?) and I seem to remember you saying you had little time for this right now, but would really like this one fixed.

bancika · March 03, 2013, 07:26:58 PM

I don't remember the issue, is it logged?

Perrow · March 04, 2013, 12:51:07 AM

Yes, by you I think.

bancika · March 04, 2013, 05:23:59 AM

there ya go

http://code.google.com/p/diy-layout-creator/downloads/list

Perrow · March 04, 2013, 05:33:57 AM

Quote from: bancika on March 04, 2013, 05:23:59 AM
there ya go

http://code.google.com/p/diy-layout-creator/downloads/list

Saw that you fixed it, but no. Still get "Could not set component type slot" error when I try to paste.

Perrow · March 04, 2013, 06:26:44 AM

Pasted the error from the log into the "issue".

bancika · March 04, 2013, 07:03:13 AM

how about now?

Perrow · March 04, 2013, 08:23:57 AM

Quote from: bancika on March 04, 2013, 07:03:13 AM
how about now?

There's no new version to download.

bancika · March 04, 2013, 08:52:21 AM

yes there is, it's the same number but with an "a" added

Perrow · March 04, 2013, 10:45:13 AM

OK, I'll look at it later.

garcho · March 04, 2013, 11:40:38 AM

QuoteSaw that you fixed it, but no. Still get "Could not set component type slot" error when I try to paste.

Quotehow about now?

It's fixed, thanks Bancika!

bancika · March 04, 2013, 02:06:23 PM

it was only there when "Continuous Creation" was ON...

garcho · March 04, 2013, 02:59:09 PM

Yes, still confirmed to work. Thanks!

Perrow · March 04, 2013, 04:23:53 PM

Yes, works fine now.

fuzzymuff · March 06, 2013, 10:47:52 PM

Noob here. First time using the DIYLC. Did I make this vero layout of the sili fuzz correctly?

fuzzymuff · March 06, 2013, 11:55:24 PM

Revised the board. How's this?

News:

DIY Layout Creator - software for easy drawing PCB, vero and perfboard layouts